{{>toc}}

h1. FTOS

Dell/Force10 S4810 48 ports 10G SFP+ + 4 ports 40G

supporte cumulus http://cumulusnetworks.com/static/cumulus/pdf/Cumulus_Networks_Dell_Datasheet.pdf

http://cumulusnetworks.com/

* ssh keys

http://www.force10networks.com/CSPortal20/TechTips/0006_RSA-SSH.aspx

https://www.dell.com/support/article/fr/fr/frbsdt1/how10657/how-to-manage-the-qsfp-ports-on-a-force10-s4810-switch?lang=en

h2. Commandes

h3. Screen

<pre>

screen -m -c /dev/null /dev/ttyUSB0 9600 8n1

</pre>

h3. Setup

<pre>

dir 

delete flash://startup-config 

reload 

no 

yes

en exec 

stop jumpstart

wr 

username force10 password force10 

enable password force10 

wr

</pre>

<pre>

portmod hybrid 

switchport

int vl 2

unttagged t0/23

int vl 3

tagged t0/23

show vlan 

stack-unit 1 renumber 0 

no 

yes

ip ssh server enable

</pre>

h3. Misc

<pre>

show inventory media 

</pre>

<pre>

show mac-address-table dynamic

show mac-address-table dynamic vlan 3132

show mac-address-table dyn int te0/0

</pre>

<pre>

Force10# sh int swi te0/0

Codes:  U - Untagged, T - Tagged

        x - Dot1x untagged, X - Dot1x tagged

        G - GVRP tagged, M - Trunk, H - VSN tagged

        i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged

Name: TenGigabitEthernet 0/0

802.1QTagged: Hybrid

Vlan membership:

Q       Vlans

U       1

T       3133-3135,3175

Native VlanId:    1.

</pre>

<pre>

show interface tengigabitethernet 0/47 transceiver

...

SFP+ 47 Temperature                      = 41.902C

SFP+ 47 Voltage                          = 3.287V

SFP+ 47 Tx Bias Current                  = 34.012mA

SFP+ 47 Tx Power                         = 0.519mW

SFP+ 47 Rx Power                         = 0.451mW

</pre>

<pre>

FTOS#sh int status

Port     Description  Status Speed     Duplex Vlan  

Te 0/0                Down   Auto      Auto   1,3131,3175,3199

Te 0/1                Up     10000 Mbit Full   1,20,128,666,3118,3131,3175,3199

Te 0/2                Up     10000 Mbit Full   3188

Te 0/3                Down   Auto      Auto   3188

Te 0/4                Up     10000 Mbit Full   3188

Te 0/5                Up     10000 Mbit Full   3188

Te 0/6                Down   Auto      Auto   3188

Te 0/7                Up     10000 Mbit Full   3188

Te 0/8                Up     10000 Mbit Full   3188

Te 0/9                Up     10000 Mbit Full   3188

Te 0/10               Down   Auto      Auto   3188

Te 0/11               Down   Auto      Auto   3188

Te 0/12               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/13               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/14               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/15               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/16               Down   Auto      Auto   1,3131-3132,3175,3199

Te 0/17               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/18               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/19               Down   Auto      Auto   1,3131-3132,3175,3199

Te 0/20               Up     10000 Mbit Full   1,3131-3132,3175,3199

Te 0/21               Up     10000 Mbit Full   1,3131-3132,3175,3199

...

</pre>

<pre>

FTOS#sh interfaces switchport tengigabitethernet 0

Codes:  U - Untagged, T - Tagged

        x - Dot1x untagged, X - Dot1x tagged

        G - GVRP tagged, M - Trunk, H - VSN tagged

        i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged

Name: TenGigabitEthernet 0/0

802.1QTagged: Hybrid

Vlan membership:

Q       Vlans

U       1

T       3131,3175,3199

Native VlanId:    1.

Name: TenGigabitEthernet 0/1

802.1QTagged: Hybrid

Vlan membership:

Q       Vlans

U       1

T       20,128,666,3118,3131,3175,3199

Native VlanId:    1.

Name: TenGigabitEthernet 0/2

802.1QTagged: Hybrid

Vlan membership:

Q       Vlans

U       3188

Native VlanId:    3188.

...

</pre>

<pre>

FTOS#sh interfaces tengigabitethernet 0           

TenGigabitEthernet 0/0 is up, line protocol is down

Hardware is DellForce10Eth, address is 00:01:e8:8b:4f:cf

    Current address is 00:01:e8:8b:4f:cf

Pluggable media not present

Interface index is 33883138

Internet address is not set

MTU 1554 bytes, IP MTU 1500 bytes

LineSpeed auto

Flowcontrol rx on tx off

ARP type: ARPA, ARP Timeout 04:00:00

Last clearing of "show interface" counters 80w0d1h

Queueing strategy: fifo

Input Statistics:

     0 packets, 0 bytes

     0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts

     0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts

     0 Multicasts, 0 Broadcasts

     0 runts, 0 giants, 0 throttles

     0 CRC, 0 overrun, 0 discarded

Output Statistics:

     0 packets, 0 bytes, 0 underruns

     0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts

     0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts

     0 Multicasts, 0 Broadcasts, 0 Unicasts

     0 throttles, 0 discarded, 0 collisions, 0 wreddrops

Rate info (interval 299 seconds):

     Input 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate

     Output 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate

Time since last interface status change: 80w0d1h

TenGigabitEthernet 0/1 is up, line protocol is up

Hardware is DellForce10Eth, address is 00:01:e8:8b:4f:cf

    Current address is 00:01:e8:8b:4f:cf

Pluggable media present, SFP+ type is 10GBASE-CU5M

    Medium is Twinax Copper

Interface index is 34145282

Internet address is not set

MTU 1554 bytes, IP MTU 1500 bytes

LineSpeed 10000 Mbit

Flowcontrol rx on tx off

ARP type: ARPA, ARP Timeout 04:00:00

Last clearing of "show interface" counters 80w0d1h

Queueing strategy: fifo

Input Statistics:

     77846344701 packets, 33998273797981 bytes

     4710063270 64-byte pkts, 40824319413 over 64-byte pkts, 9871182555 over 127-byte pkts

     3982474520 over 255-byte pkts, 684219485 over 511-byte pkts, 17774085458 over 1023-byte pkts

     64436920 Multicasts, 108058987 Broadcasts

     0 runts, 0 giants, 0 throttles

     0 CRC, 0 overrun, 0 discarded

Output Statistics:

     100565862739 packets, 85221880135780 bytes, 0 underruns

     5520274128 64-byte pkts, 32394947465 over 64-byte pkts, 5238057644 over 127-byte pkts

     2670375206 over 255-byte pkts, 2001008247 over 511-byte pkts, 52741200049 over 1023-byte pkts

     300101222 Multicasts, 601777166 Broadcasts, 99663984351 Unicasts

     0 throttles, 0 discarded, 0 collisions, 0 wreddrops

Rate info (interval 299 seconds):

     Input 00.00 Mbits/sec,        217 packets/sec, 0.00% of line-rate

     Output 00.00 Mbits/sec,        237 packets/sec, 0.01% of line-rate

Time since last interface status change: 1w5d1h

...

</pre>

h3. Switch Openstack

On se logue

<pre>

enable password force10 

conf

</pre>

Preparation des ports

<pre>

int range tengigabitethernet 0/0 - 47

no switchport

portmod hybrid 

switchport

no shut

int range fortyGigE 0/48 - 60

no switchport

portmod hybrid 

switchport

no shut

# Pour le port uplink

int range tengigabitethernet 0/1

speed 1000

</pre>

Pour un seul port :

<pre>

enable

conf

int t0/10

speed 1000

exit

exit

wr

# ou do wr

</pre>

Au cas ou "no negotiation auto" peut aider (cas des SFP bidi alturna CISCO) :

<pre>

FTOS(conf-if-te-0/16)#negotiation ?

auto                	Perform link autonegotiation            

FTOS(conf-if-te-0/16)#speed ?     

10                  	10 Mbps                                 

100                 	100 Mbps                                

1000                	1000 Mbps                               

10000               	10000 Mbps                              

auto                	Auto negotiation (default)   

</pre>

Creation des vlans

<pre>

int vlan 3131

no shut

int vlan 3175

ip address 192.168.3.48/24

no shut

int vlan 3195

no shut

int vlan 174

no shut

</pre>

Ajout des ports au vlan

<pre>

int vlan 3131

tagged tengigabitethernet 0/1

tagged tengigabitethernet 0/5

tagged tengigabitethernet 0/7

tagged tengigabitethernet 0/9

int vlan 3132

tagged tengigabitethernet 0/1

tagged tengigabitethernet 0/5

tagged tengigabitethernet 0/7

tagged tengigabitethernet 0/9

int vlan 3175

tagged tengigabitethernet 0/1

tagged tengigabitethernet 0/5

tagged tengigabitethernet 0/7

tagged tengigabitethernet 0/9

int vlan 3199

tagged tengigabitethernet 0/1

tagged tengigabitethernet 0/5

tagged tengigabitethernet 0/7

tagged tengigabitethernet 0/9

</pre>

Pour le TouIX untagged 4031

<pre>

FTOS>enable

FTOS#conf

FTOS(conf)#int vlan 4031

FTOS(conf-if-vl-4031)#no shut

FTOS(conf-if-vl-4031)#description TouIX

FTOS(conf-if-vl-4031)#untagged tengigabitethernet 0/35

FTOS(conf-if-vl-4031)#exit

FTOS(conf)#wr

</pre>

Detruire un vlan

<pre>

no int vlan2

</pre>

Enlever un port d'un vlan

<pre>

int vlan 2

no tagged tengigabitethernet 0/1

</pre>

Configuration routage

<pre>

ip route 0.0.0.0/0 192.168.3.47

</pre>

Configuration du logging

<pre>

logging 91.224.149.152

</pre>

Fabrication port bonding

<pre>

- enable

- conf

- int tengigabitethernet 0/46

- port-channel-protocol lacp

- port-channel 10 mode active

- no shut

- int tengigabitethernet 0/47

- port-channel-protocol lacp

- port-channel 10 mode active

- no shut

- exit

- int port-channel 10

- sw

- no shut

- end

- wr

</pre>

tcpdump

<pre>

FTOS#tcpdump cp packet-count 10

% Copy operation not allowed until the TCP dump completes %

FTOS#dir flash:/TCP_DUMP_DIR/Tcpdump_141014021344/ 

</pre>

h3. 40G

40G to 4x10G  : reboot necessaire

http://www.dell.com/support/article/us/en/19/how10657/how-to-manage-the-qsfp-ports-on-a-force10-s4810-switch?lang=en